RBM-1300RMB-1600MIG-210TIG-200PTIG-200DPInput voltage220V220V220V/110V220V220V/110VCurrent range30-130A30-160A30-140A/30-180A5-200A5-200A/5-150ADuty-cycle 60%85%60%60%60%Welding WireFlux Cored Wire(FCAW)Solid/Flux Cored Wire(FCAW)Solid/Flux Cored Wire(FCAW)Diameter of wire 030″-.035″(0.8/1.0 mm ) 030″-.035”(0.8/1.0 mm ).030″-.035″(0.8/1.0 mm )FunctionMIG/Stick/Lift TIGMIG/Stick/Lift TIGMIG/Stick/Lift TIGTIG/ TIG Pulse/ StickTIG/ TIG Pulse/ StickWelding thicknessover.030″(0.8mm)over .030″(0.8mm)- .035″ (1.0mm) over .030″(0.8mm) 3/8″ 3/8″Welding MaterialCarbon Steel/Mild Steel/Other Metal materialStainless steel/Carbon Steel/Mild Steel/Other Metal materialStainless steel/Carbon Steel/Mild Steel/Other Metal materialStainless steel/Carbon Steel/Mild Steel/Other Metal material Aluminum/Stainless steel/Carbon Steel/Mild Steel/Other Metal materialPackage Weight20.28bl26.46bl28.2bl26.89lb26.89lbDimensions 415×273×310mm535×305×345mm540×310×350mm 440×380×360mm 440×380×360mm Use a metal brush or grinder and clean down to bare metal before striking an arc. A fillet weld, shown here, is one of the most common types of welds. In the flat position, keep the gun angled at 45 degrees from each piece. Whether you weld vertical up or down will depend on the application and the thickness of the material you are welding. You’ll want to direct more heat into the bottom piece of metal when welding a lap joint. A 60 to 70 degree angle is usually best. Read more Troubleshooting Why is my MIG-130 Welder not welding correctly? 1. Wire feed tension: Check the tension on the spooler. Is it set too tight or is the wire feed tension not set correctly? 2. Wire choice: Are you using .035” wire? We recommend .025-0.30″ for best performance. 3. Stick out: Is your stick out too long? Your stick out should be no more than ½”. 4. Pull the trigger: To begin welding, pull the trigger on the MIG gun. 5. Proper grounding: The ground should not be attached to painted or coated metal. Read more Efficient: 85 % Wire feeder : Inside Power factor cosf 0.93 Welding thickness: =0.8mm Diameter of wire: 0.8/1.0mm Dimensions: 415×273×310MM Weight : 9.2KG MIG/LIFT TIG/MMA STICK 3 in 1 WELDING MACHINE Input power voltage: AC220±15% V Rated input power capacity: 4.5KVA Input current :16A for MIG,21A for MMA Rated output current :130 A Duty-cycle: 60% Output current range :30-130 A Output voltage range :15-19V Insulation class : F Protection class : IP21S Read more Factory Production Process Control System 1,Compoents quality control with fan, on-off swtich ,power cord with 100% production test before delivery . 2.Package kit check to assure all welding accessories including. 3.Carry out welding performance test, life test ,function test and temperature test. 4.Mass production capacity with 10000pcs per week. We will take each and every action to prevent you from bearing any loss at Amazon as we value our customer’s investment and trust more than anything else. Read more
Make sure this fitsby entering your model number.
?Look at the panel,it is easy to set the parameters. the mig130 supports with 1kg flux cored wire most perfectly to do the carbon steel welding without gas.mig/mma ,gas/gasless all are available ,mma welding(3.2mm rod) 7018 1/8 very well
also 6013 and 7018 3/32″”
#47,998 in Automotive (See Top 100 in Automotive)#78 in MIG Welding Equipment
16-Jan-20
0
FALSE
Related products
$86.00
